Oasis WP2D

  • Buy:

Oasis deep well hand pump with blue body HAS BLUE BODY LIKE THE PHOTO OF THE WP2-1

NOTE: IF YOU WANT A DIFFERENT HANDLE ORIENTATION THAN SHOWN IN THE PHOTO JUST SEND ME AN EMAIL DESCRIBING THE DESIRED HANDLE POSITION

Made in the USA of ABS and PVC plastic with stainless steel pump rod and fasteners, the Oasis pump is light weight and will not rust or corrode.

This hand pump set is capable of pumping water from depths of up to 50 Feet.

The closed design helps prevent contaminants from entering the well Water can be pumped to another location and overhead by attaching a 1 1/4” hose to the discharge spout. Can be made freeze proof by drilling a 1/16” hole in the drop pipe below the frost line - after you stop pumping the water above the hole drains back down the well.

Has a sealed top chamber (which repels rain) and is recommended for drinking water

PUMP STAND SPECIFICATIONS: (The component that sits above the well).

  • Height: 24” (90 cm) and can be easily modified to suit.
  • Base Diameter: 7” (17.5 cm) Weight: 6 lbs (2.8 kg)
  • Discharge Port: 1 1/4” female pipe thread with vermin screen, and elbow with 1 1/4" female pipe thread Suction Port: 2” female pipe thread for drop pipe.
  • Pump Rod Size: 3/8” diameter with adapter to 1/2” rigid PVC plastic pipe
  • Pump Rod Stroke: 3 1/2” (9 cm) All fasteners and the upper pump rod are stainless steel.

 

CYLINDER SPECIFICATIONS: (The component that goes down the well).

  • CYL 002F Height: 29” (72.5 cm)
  • Outside Diameter: 3 1/8” (7.5 cm)
  • Inside Diameter: 2” (5.0 cm)
  • Weight: 5 lbs (2.6 kg)
  • Pipe Size: 2” PVC slip fitting (solvent weld)
  • Plunger: All Brass with 2 cup leathers and stainless steel pump rod adapter.
  • Pump Rod Size: 1/2” PVC Cylinder Barrel: made of rigid PVC.
  • Capacity: approximately 2 G.P.M. at 50 strokes per minute

NOTE: To use this hand pump as a backup to an electric submersible pump during a power failure, the above PVC cylinder can be replaced with a brass cylinder (1 13/16" inside diameter, 2" outside diameter) which will more easily fit inside a well casing beside the water line coming from the submersible pump. Please contact us for the price and further information.

MAJOR COMPONENTS The major components of a complete installation are as follows:

  • (1) PUMP STAND The base is attached to a platform above the well casing (using 1/4” fasteners (4 required)wp2ds Has 2” female pipe thread to attach the drop pipe Has stainless steel upper rod with adapter to attach pump rod.
  • (2) DROP PIPE (2” rigid PVC plastic) - NOT INCLUDED Connects the pump stand to the well cylinder and carries the water to the surface Comes in 10 foot lengths, and can be glued (solvent welded) or screwed together using couplers purchase locally
  • (3) PUMP ROD (1/2” rigid PVC plastic) - NOT INCLUDED Located inside the drop pipe and connects the pump handle to the plunger assembly in the cylinder this hollow pump rod actually floats and therefore reduces the pumping effort Comes in 10 foot lengths, and can be glued (solvent welded) or screwed together using couplers purchase locally
  • (4) WELL CYLINDER (2 I.D. made of rigid PVC plastic) Has a brass plunger with 2 cup leathers, and is the actual pumping component that goes down the well the up and down movement of the plunger (activated by the pump handle and pump rod) brings the water to the surface Has adapter to connect to the pump rod. Has external foot valve
  • NOTE: Enough drop pipe and pump rod is required to locate the cylinder 15ft below the surface of he water.
  • (5) PLATFORM - NOT INCLUDED Can be fabricated from wood or steel and must be high enough to allow access to the well seal bolts
  • (6) WELL SEAL - NOT INCLUDED Used to seal the top of the well casing where the drop pipe goes in
  • (7) WELL CASING - NOT INCLUDED Installed by a well driller - 4, 5 and 6” are common sizes The 2” rigid PVC plastic pipe used as the drop pipe, the 1/2” rigid PVC plastic pipe used as the pump rod and the well seal can be purchased locally at a plumbing store, or can be ordered from us - please contact us for details.

About Rintoul's Hand Pumps

Established in 1983, Rintoul's Hand Pumps has provided quality pump products across the globe for many applications. We take pride in supplying the best products, and are available for all your questions!

Where are we?

Rintoul's Hand Pumps

519-371-3500

285 8th St E
Owen Sound, ON N4K 1L2
Canada

©2024 RINTOUL'S HAND PUMPS. All Rights Reserved. Designed By NewMedia Designs

Search